ICF Price Calculator: Blocks Needed & Installed Wall Cost

Work out how many insulated concrete form (ICF) blocks a wall needs from the wall area and the coverage of each block, or estimate the installed cost of an ICF wall.

Construction — Other Calculators

ICF Price Calculator

Insulated concrete form (ICF) wall cost from wall area, block count and installed cost per ft².

Starting values: a wall area of 800 ft² and blocks that cover 4.5 ft² each, which needs 178 blocks. The cost mode starts at an installed price of 12 per ft², which gives 9,600.

How the calculator works

Blocks needed

Blocks = wall area ÷ coverage per block, rounded up

The coverage per block is your input. The starting value of 4.5 ft² is a general figure, and the real value depends on the block you buy, so use the face area from the manufacturer. The result is rounded up to a whole block.

Installed cost

Total = wall area × installed cost per ft²

The installed price is your input, with a starting value of 12, which is an example. The inputs have unit selectors, so you can use square metres.

Worked examples

The starting wall

800 ÷ 4.5 = 177.8, which rounds up to 178 blocks.

Using a standard block

A building guide says that an ICF block is about 48 in long and 16 in tall, so one block covers about 5.3 ft². Using 5.33 ft² for the same wall: 800 ÷ 5.33 = 150, so 150 blocks. The 28 block difference shows why you should enter the coverage of your own block.

A basement wall

A wall 8 ft high and 100 ft long has an area of 800 ft², and the same result as above. A wall 9 ft high and 120 ft long is 1,080 ft², which needs 1,080 ÷ 5.33 = 202.5, so 203 blocks.

Cost

A wall of 800 ft² at an installed price of 12 per ft² costs 9,600. Use a figure from a quote, since the starting value is only an example.

About ICF walls

The same guide describes how an ICF wall is built. The blocks are hollow forms of foam that stack like building blocks, and the hollow core is filled with concrete and steel reinforcing bar. Key points:

  • Size. The overall thickness varies from 4 to 12 in. The concrete core is usually 4 to 10 in, and 6 in is the most common for homes. With foam of 2.5 in on each side, a 6 in core makes a wall 11 in thick.
  • Footing. The footing should extend about 2 in past each face, so an 11 in wall needs a footing at least 15 in wide.
  • Reinforcement. Vertical bars run through the cores about 16 to 48 in apart, and horizontal bars sit in the grooves of the blocks.
  • Pouring. The concrete is usually pumped in lifts of 3 to 4 ft, and the forms stay in place for at least 7 days.
  • Openings. Windows and doors need blockouts before the pour.

What the estimate leaves out

The block count uses the wall area only. It does not subtract the windows and doors, and it does not add an allowance for cut blocks and waste, so adjust the area for the openings, and add an allowance. The cost mode gives a total for the wall and does not separate forms, concrete, steel and labour.

Cost compared with other walls

The guide says that the forms cost more per square foot than block or cast-in-place walls alone, but that once insulation and finishing are counted, the finished wall is competitive with them. It also says the heating and cooling savings of an ICF building can offset some of the higher price over time. Ask for quotes on the same basis before you compare.

For the concrete, see the concrete cost calculator and the concrete wall calculator. For block walls, see the block wall calculator and the block wall cost calculator. For the foundation, see the foundation cost calculator.

Planning an ICF order

Before you order blocks, confirm the type of block with the supplier, since the dimensions, the core thickness and the corner and brick-ledge pieces differ between products. Ask for the face area of a standard block, and whether corner blocks, tapered tops and other specials are counted separately from the straight blocks.

Adjusting the wall area

Work out the gross wall area first, then take off the windows and doors that will have blockouts. For example, a wall of 1,080 ft² with two openings of 15 ft² each leaves 1,050 ft², and at 5.33 ft² per block that needs 1,050 ÷ 5.33 = 197 blocks. Then add an allowance for cuts and waste, as agreed with your supplier, and round up to a whole pallet if blocks are sold that way.

Checking the cost

Divide a quoted price by the wall area to get the installed rate per square foot, and enter that in the cost mode. This makes the estimate reflect your own quote, and it lets you test a larger or smaller building quickly.

Frequently asked questions

How many ICF blocks do I need?

Divide the wall area by the face area of one block and round up. A wall of 800 ft² with blocks of 5.33 ft² needs 150 blocks.

How big is an ICF block?

A building guide says a block is about 48 in long and 16 in tall, so it covers about 5.3 ft². Check the face area of your own block.

How thick is an ICF wall?

The overall thickness varies from 4 to 12 in. A 6 in concrete core with 2.5 in of foam on each side makes a wall 11 in thick.

Does the calculator subtract windows and doors?

No. It uses the wall area you enter, so subtract the openings yourself and add an allowance for cuts and waste.

Mark Danny

Mark Danny

Mark Danny builds and maintains the free calculators and guides on Area of Irregular Shapes Calculator. Every calculator page explains its formula and shows a worked example, so you can check the working yourself. Spotted a mistake or have a suggestion? Email gulsher.hingoro101@gmail.com.

Articles: 559