Water Damage Repair Cost Calculator: Estimate by Area & Category

Water damage repair is priced by how much floor area is affected and by how dirty the water was. This water damage repair cost calculator multiplies the affected floor area by a cost per square foot for the water category you choose: clean, grey or black water.

Construction — Other Calculators

Water Damage Repair Cost Calculator

Water damage restoration cost from affected area and damage category (clean water, grey water, black water/sewage).

The starting values are 300 square feet of Category 1 (clean) water damage at $4 per square foot, which gives $1,200.

How is water damage repair cost calculated?

Multiply the affected floor area by the cost per square foot for the water category.

Total = Area × Cost per sq ft

Where area is the affected floor area in square feet and the cost per square foot depends on the category. The calculator uses $4 for Category 1, $6 for Category 2 and $8.50 for Category 3.

Worked example: the starting values

Total = 300 × 4 = $1,200

The same 300 square feet costs 300 × 6 = $1,800 with grey water and 300 × 8.50 = $2,550 with black water.

Worked examples for different losses

Worked examples

Small leak

Enter 150 square feet of Category 1 damage. The result is 150 × 4 = $600.

How the area and the category change the cost

The table shows four affected areas at each of the three categories.

Area Category 1 ($4) Category 2 ($6) Category 3 ($8.50)
100 sq ft $400 $600 $850
300 sq ft $1,200 $1,800 $2,550
600 sq ft $2,400 $3,600 $5,100
1,000 sq ft $4,000 $6,000 $8,500

The category changes the rate by more than double between the cleanest and the dirtiest water, so the first job is to establish which category applies. A restoration professional can tell you after inspecting the water source and the materials that it has touched.

Why the category matters

Category 1 water comes from a clean source, such as a supply line. Category 2 water carries some contamination, for instance from an appliance. Category 3 water is heavily contaminated, such as sewage or flood water, and the affected materials usually have to be removed and not dried. This is why the rate rises, and why a contaminated loss needs a professional and not a do-it-yourself repair.

Measuring the affected area

Measure the floor area that was wet, by length and width, and add the rooms together. Include the area under cabinets and along the walls where the water has travelled, since moisture spreads further than the visible damage. A restoration company can check the extent with a moisture meter.

Insurance and the estimate

Before you start, read your insurance policy to see what it covers and what it requires you to do, and photograph the damage first. Keep the calculator figure as your own reference, and compare it with the estimate from the insurer and from the contractor. If the numbers differ a lot, ask for a breakdown of the items and the quantities.

What the rate may not include

The rate is a rough figure for the repair. It does not include replacing the contents of the room, the repair of damage to the structure, or the cost of finding and fixing the leak. Treat it as a first estimate and expect the final cost to depend on the inspection.

If the damage covers more than one room, run the calculator once for each category that applies and add the results, because a single loss can include both clean and contaminated areas.

Photograph the damage and keep the receipts for any emergency work, since they support an insurance claim and give the contractor a reference for the extent of the loss.

Frequently asked questions

What is the difference between clean, grey and black water?

Clean water comes from a clean source, grey water from appliances and toilet bowls, and black water from sewage or flooding.

Which water category should I enter?

Use the one a restoration professional gives you after inspecting the source of the water. Category 1 is clean, Category 2 has some contamination and Category 3 is heavily contaminated.

How much more does contaminated water cost to repair?

At the calculator’s rates, 300 sq ft costs $1,200 in Category 1 and $2,550 in Category 3.

How do I measure the affected area?

Measure the wet floor area and add the rooms. Include the area under cabinets and along the walls, because moisture spreads further than you can see.

Mark Danny

Mark Danny

Mark Danny builds and maintains the free calculators and guides on Area of Irregular Shapes Calculator. Every calculator page explains its formula and shows a worked example, so you can check the working yourself. Spotted a mistake or have a suggestion? Email gulsher.hingoro101@gmail.com.

Articles: 559