Calculate how many tons of asphalt a paving job needs from the area and thickness, convert square yards to tons, or estimate the installed cost.
Asphalt Calculator
Asphalt tonnage and installed cost for a driveway or lot, from area and paving thickness — includes a general square-yards-to-tons conversion.
Starting values: an area of 1,000 ft² at a thickness of 3 in, which needs 18.1 tons of asphalt. The cost mode starts at an installed price of 5 per ft², which gives 5,000.
How the calculator works
Tonnage
Tons = area × thickness × density ÷ 2,000
Where the area is in ft², the thickness is in feet, and the density is 145 lb per ft³ of compacted asphalt. The calculator note says compacted density varies with the mix, roughly 140 to 150 lb per ft³, and that 145 is a typical mid-range figure. The tons are US tons of 2,000 lb.
Square yards to tons
The same formula, with the area entered in square yards. It is the quick way to use a quote or a plan that is in square yards.
Installed cost
Total = area × installed cost per ft²
The installed price is your input, and the starting value of 5 is an example. The inputs have unit selectors, so you can use inches or millimetres for the thickness.
Worked examples
The starting job
A thickness of 3 in is 0.25 ft, so the volume is 1,000 × 0.25 = 250 ft³. At 145 lb per ft³ that is 36,250 lb, which is 18.1 tons.
A driveway
A driveway of 480 ft² at 2 in thick has a volume of 480 × 0.1667 = 80 ft³, which is 11,600 lb, or 5.8 tons. At 3 in it is 120 ft³, which is 17,400 lb, or 8.7 tons.
From square yards
An area of 500 yd² at 3 in: 500 yd² is 4,500 ft², and the volume is 4,500 × 0.25 = 1,125 ft³, which is 163,125 lb, or 81.6 tons.
A parking lot
An area of 5,000 ft² at 4 in: the volume is 1,666.7 ft³, which is 241,667 lb, or 120.8 tons.
Cost
A job of 1,000 ft² at an installed price of 5 per ft² costs 5,000. Use a figure from a quote, since the starting value is only an example.
Checking against a rule of thumb
A paving guide gives a rule of 110 lb of asphalt per square yard for each inch of thickness. For an area of 1,000 ft² at 2 in, that is 111.1 yd² × 2 × 110 ÷ 2,000 = 12.2 tons. The calculator gives 12.1 tons for the same job, which is within a percent. The two methods agree because 145 lb per ft³ is about 108.75 lb per square yard per inch.
How thick should the asphalt be
The guide gives about 2 to 3 in of compacted asphalt for a residential driveway, and about 4 to 6 in for a commercial parking lot, laid over a compacted base of aggregate. Ask your paving contractor for the thickness that suits your soil and traffic, since the loads on a drive and a lot are different.
Adding an allowance
The calculator gives the weight for the area and the thickness that you enter. Real jobs use a bit more, because the ground is not perfectly even and the edges need material. The guide recommends adding a 5 percent margin to cover variations in the base. For the 12.1 tons of the 2 in example, that is about 12.7 tons. Your supplier can say how much to order.
Related calculators
To find the area of a driveway, see the driveway square footage calculator. For a larger lot, see the parking area calculator and the parking lot paint calculator. For concrete in place of asphalt, see the concrete cost calculator.
Planning a paving job
The tonnage is only one part of the job. The base under the asphalt matters as much as the asphalt itself, since the guide describes the asphalt as laid over a compacted aggregate base for a parking lot. A weak or uneven base shortens the life of the surface, so ask your contractor how they will prepare it.
Ordering the material
Asphalt is made to order and laid hot, so you need the quantity right on the day. Ask the supplier how they sell it, usually by the ton, and how much they advise for your area and thickness. Order a little more than the calculated weight to cover the variations in the base, and plan for the truck access to the site.
Comparing quotes
If a contractor quotes by the square foot, use the cost mode and compare with the calculated tonnage and the price per ton that you are given. A quote should say the thickness, the area, the type of base and whether the removal of an old surface is included. Compare quotes on the same basis, and use the calculator as a check on the quantity.
Frequently asked questions
How do I calculate the tons of asphalt for a driveway?
Multiply the area in ft² by the thickness in feet and by 145 lb per ft³, then divide by 2,000. A driveway of 480 ft² at 3 in needs about 8.7 tons.
How thick should asphalt be?
A paving guide gives about 2 to 3 in of compacted asphalt for a residential driveway and about 4 to 6 in for a commercial parking lot, over a compacted base.
How many pounds of asphalt are in a square yard?
A paving guide uses 110 lb per square yard for each inch of thickness. The calculator uses 145 lb per ft³, which is about 108.75 lb per square yard per inch.
Should I order extra asphalt?
The guide recommends about 5 percent extra to cover variations in the base. Your supplier can advise.
