Air Source Heat Pump Cost Calculator: Installed Cost by System Size

An air-source heat pump installation is usually quoted by system size, measured in tons. This air source heat pump cost calculator multiplies the system size in tons by the installed cost per ton, then adds an optional amount for ductwork changes. It starts with a 3-ton system at $2,200 per ton, which are placeholders, so use the per-ton figure from your own quotes.

Heating & Cooling Cost Calculators

Air Source Heat Pump Cost Calculator

Installed cost of an air-source heat pump system, from unit size (tons) and installation complexity.

tons
$
Example price — replace with your local quote.
$

How do you calculate air source heat pump cost?

Multiply the tons by the installed cost per ton, then add the ductwork amount.

Total = System size (tons) × Cost per ton installed + Ductwork modifications

Where:

  • System size = the capacity of the heat pump in tons
  • Cost per ton installed = the price per ton including installation, from your quote
  • Ductwork modifications = a lump sum for changes to ducts, or 0 if none

Worked examples

Worked example: the calculator’s starting values

Total = 3 × 2,200 + 0 = $6,600

Worked example: with ductwork changes

A 4-ton system at $2,200 per ton, with $2,500 of ductwork changes:

Total = 4 × 2,200 + 2,500 = 8,800 + 2,500 = $11,300

Worked example: a higher quote

A 3-ton system quoted at $2,800 per ton, with $1,800 for ductwork:

Total = 3 × 2,800 + 1,800 = 8,400 + 1,800 = $10,200

System size and cost compared

At the $2,200 starting rate and no ductwork:

System size Total
2 tons $4,400
3 tons $6,600
4 tons $8,800
5 tons $11,000

What is a ton of heat pump capacity?

A ton of capacity is 12,000 BTU per hour, a standard unit for heating and cooling equipment. A 3-ton system therefore has a nominal capacity of 36,000 BTU per hour. The calculator takes your tons as an input and does not work out the size you need from your home. Sizing depends on your home’s heat loss and climate, so ask your installer for a load calculation.

What the per-ton price covers

The calculator uses one installed price per ton. What that covers depends on the quote, so ask what it includes. It may include the outdoor unit, the indoor unit, refrigerant lines, electrical connections, a thermostat and labor. Ask also whether removal of an old system is part of it.

What the ductwork amount is for

If your home already has ducts that suit the new system, you may enter 0. If the ducts need changes or repairs, enter the quoted amount. Homes without ducts may need a different type of system, so ask your installer about the options.

What the air source heat pump cost calculator leaves out

It does not include electrical panel upgrades, permits, removal of the old equipment, or incentives and rebates, unless your per-ton figure already covers them. It also gives the purchase cost only, not the running cost. For running costs, compare systems with the heating system cost comparison calculator.

Comparing heat pump quotes

Ask each installer for the system size, model, efficiency ratings, what is included and the total. Divide each total by the tons to compare per-ton prices, and check that ductwork and electrical work are treated the same way.

Price per ton and total compared

For a 3-ton system with no ductwork:

Cost per ton installed Total
$1,800 $5,400
$2,200 $6,600
$2,600 $7,800
$3,000 $9,000

What ductwork can add

For a 3-ton system at $2,200 per ton:

Ductwork amount Total
$0 $6,600
$1,500 $8,100
$3,000 $9,600

BTU by system size

Tons Nominal BTU per hour
2 24,000
3 36,000
4 48,000
5 60,000

Worked examples

Worked example: turning a quote into a per-ton price

Two installers quote a 3-ton system. Installer A quotes $9,500 including ductwork, and installer B quotes $8,400 with no ductwork changes:

A: 9,500 ÷ 3 = $3,167 per ton
B: 8,400 ÷ 3 = $2,800 per ton

The quotes may not cover the same work, so ask A how much of the price is ductwork. If it is $1,800, A’s per-ton price for the equipment and install is (9,500 − 1,800) ÷ 3 = $2,567.

Worked example: subtracting an incentive

If you qualify for an incentive of $1,500 on the $10,200 system from the earlier example, subtract it yourself: 10,200 − 1,500 = $8,700. The calculator does not include rebates, and the amount depends on where you live and the scheme.

Ductwork, labour and permits

The ductwork box is the item most likely to change the total, so check it against published prices.

Before you sign a quote

Ask the installer how the system size was chosen, since an estimate based on a load calculation is more reliable than one based on the floor area alone. Ask for the model number and the efficiency rating so you can compare the equipment between quotes, and confirm in writing what happens if the home needs a larger electrical supply once the work begins.

Frequently asked questions

Mark Danny

Mark Danny

Mark Danny builds and maintains the free calculators and guides on Area of Irregular Shapes Calculator. Every calculator page explains its formula and shows a worked example, so you can check the working yourself. Spotted a mistake or have a suggestion? Email gulsher.hingoro101@gmail.com.

Articles: 559