Baseboard Heater Calculator: Size & Running Cost

Electric baseboard heaters are sized by wattage and sold in lengths, and running them costs money by the hour. This baseboard heater calculator takes your room area, electricity rate and hours of use per day, and returns the recommended wattage, the length of baseboard needed and the estimated daily running cost. It starts with a 150 ft² room, $0.15 per kWh and 6 hours a day.

Heating & Cooling Cost Calculators

Baseboard Heater Calculator

Electric baseboard heater length and running cost for a room, from room area and your electricity rate.

$
per kWh

How do you calculate baseboard heater size?

Multiply the room area by 10 watts per square foot, then divide by 250 watts per foot of baseboard for the length. The daily cost then follows from the wattage, the hours the heater runs and your electricity rate, as the formulas below show.

Wattage = Room area (ft²) × 10
Baseboard length (ft) = Wattage ÷ 250
Daily cost = (Wattage ÷ 1,000) × Hours per day × Rate per kWh

The 10 W per ft² and the 250 W per foot are values built into the calculator. They are rules of thumb, not a replacement for a heat-loss calculation.

Worked examples

Worked example: the starting values

A 150 ft² room, $0.15 per kWh, 6 hours a day:

Wattage = 150 × 10 = 1,500 W
Length = 1,500 ÷ 250 = 6 ft
Daily cost = 1.5 × 6 × 0.15 = $1.35

Worked example: a small bedroom

A 120 ft² room, $0.20 per kWh, 4 hours a day:

Wattage = 1,200 W
Length = 1,200 ÷ 250 = 4.8 ft
Daily cost = 1.2 × 4 × 0.20 = $0.96

Worked example: a large living room

A 300 ft² room, $0.12 per kWh, 8 hours a day:

Wattage = 3,000 W
Length = 3,000 ÷ 250 = 12 ft
Daily cost = 3.0 × 8 × 0.12 = $2.88

Room size and heater output compared

At $0.15 per kWh and 6 hours a day:

Room area Wattage Length Daily cost
100 ft² 1,000 W 4 ft $0.90
150 ft² 1,500 W 6 ft $1.35
200 ft² 2,000 W 8 ft $1.80
300 ft² 3,000 W 12 ft $2.70

Monthly cost and thermostat cycling

Multiply the daily figure by the number of days. For the starting room, 30 days at $1.35 is $40.50. The calculator assumes the heater draws its full wattage for all the hours you enter. A thermostat cycles the heater on and off, so real running time is often less. Use hours the heater actually runs for a better figure.

Baseboard heater output in BTU

An electric heater turns each watt into 3.412 BTU per hour. For 1,500 W that is 1,500 × 3.412 = 5,118 BTU/h. Check the heater’s label for its rated wattage and its length, since models differ.

What the baseboard heater calculator assumes

The calculator uses one watts-per-square-foot figure for every room. It does not consider insulation, climate, ceiling height, windows or whether the room is on an outside wall. A poorly insulated room in a cold climate needs more than the rule of thumb, and a well-insulated one less. For a firm answer, get a heat-loss calculation.

Where to place baseboard heaters

Put them where heat loss is greatest, often under windows on outside walls, and keep furniture and curtains clear of them. Follow the manufacturer’s instructions on clearances and wiring. Heaters are made in set lengths, so you may need two shorter units rather than one long one.

Electricity rate and daily cost compared

For a 1,500 W heater running 6 hours a day, the heater uses 9 kWh a day, so the cost is 9 times your rate:

Rate per kWh Daily cost
$0.10 $0.90
$0.15 $1.35
$0.20 $1.80
$0.30 $2.70

Hours of use and daily cost compared

For the same heater at $0.15 per kWh:

Hours per day Daily cost 30 days
2 hours $0.45 $13.50
4 hours $0.90 $27.00
6 hours $1.35 $40.50
8 hours $1.80 $54.00

Worked example: an open-plan room

A 400 ft² room at $0.14 per kWh, 5 hours a day:

Wattage = 400 × 10 = 4,000 W
Length = 4,000 ÷ 250 = 16 ft
Daily cost = 4.0 × 5 × 0.14 = $2.80

How do you split the length across several heaters?

The calculator gives one total length. For the open-plan room that is 16 ft, which you might split across two or three units on different walls. Add up the rated wattage of the heaters you choose and compare it with the 4,000 W result. Check each model’s length and wattage on its label, because they differ between makes.

Worked example: two rooms with different sizes

A 150 ft² room and a 120 ft² room, $0.15 per kWh, 6 hours a day:

Total area = 150 + 120 = 270 ft²
Wattage = 270 × 10 = 2,700 W
Length = 2,700 ÷ 250 = 10.8 ft
Daily cost = 2.7 × 6 × 0.15 = $2.43
Heat = 2,700 × 3.412 = about 9,212 BTU/h

Run each room on its own if the hours or the heaters differ, then add the results.

Adjusting the wattage for insulation and ceiling height

Worked example: an older room with a high ceiling

Enter the area in the calculator, then apply the adjustments yourself. At $0.15 per kWh and 6 hours a day, the 1,875 W result costs 1.875 × 6 × 0.15 = about $1.69 a day, against $1.35 for the plain 1,500 W result.

Circuit size and 120 V or 240 V heaters

Wattage also decides what wiring the heaters need. InspectApedia gives a 20 A, 120 V circuit up to 1,920 W of baseboard heat and a 20 A, 240 V circuit up to 3,840 W.

Does 240 V cost less to run?

No. InspectApedia says voltage does not change the operating cost, but 240 V can lower the installation cost when several heaters share one circuit.

Matching heater and circuit

HomElectrical warns never to connect a 120 V heater to a 240 V supply or the reverse, and says a 240 V heater will not work properly on a 120 V circuit. Only a licensed electrician should do the wiring, and local code decides the rest.

Baseboard, hydronic and fan heaters compared

Electric baseboard turns all the electricity into heat, but it is not the cheapest way to heat. InspectApedia says electric heat is 100 percent efficient at the point of use, yet baseboard is the most expensive per BTU of output in most of North America. It adds that a baseboard takes 30 to 40 minutes to warm a room, against under 10 minutes for a fan heater, and that baseboard lasts 20 years or more against 8 to 12 for a fan heater.

Hydronic baseboard uses a different rule

HomElectrical sizes hydronic baseboard at 34 BTU per ft², then divides the total by 600 for the length. A 120 ft² room needs about 6.8 ft of hydronic baseboard, against 4.8 ft of electric at this calculator’s 10 W per ft². This calculator covers electric baseboard only.

Frequently asked questions

How many feet of baseboard do I need for a room?

Divide the wattage by 250 W per foot. A 1,500 W room needs 6 ft of baseboard.

How many baseboard heaters can I put on one circuit?

As many as keep the total wattage within the circuit. InspectApedia gives up to 1,920 W on a 20 A, 120 V circuit and 3,840 W on a 20 A, 240 V circuit.

Is a 240 V baseboard heater cheaper to run than a 120 V one?

No. InspectApedia says voltage does not change the operating cost, although 240 V can lower the installation cost.

Why is my real bill lower than the estimate?

The calculator assumes the heater draws full wattage for every hour you enter. A thermostat cycles the heater off and on, so enter the hours it actually runs.

Mark Danny

Mark Danny

Mark Danny builds and maintains the free calculators and guides on Area of Irregular Shapes Calculator. Every calculator page explains its formula and shows a worked example, so you can check the working yourself. Spotted a mistake or have a suggestion? Email gulsher.hingoro101@gmail.com.

Articles: 559