Heat Tracing Calculator: Pipe Freeze Protection Cable Length & Wattage

Work out how much self-regulating heat cable a pipe needs, and its running wattage, from the pipe length, the way the cable is run and the cable output.

Heating & Cooling Cost Calculators

Heat Tracing Calculator

Self-regulating heat cable length and running wattage for pipe freeze protection, from pipe length and wrap style.

W/ft

Starting values: a pipe run of 100 ft, a straight cable run and a cable output of 5 W per foot. The calculator gives 100 ft of cable and a running wattage of 500 W.

How the calculator works

Cable length = pipe length × wrap multiplier

Running wattage = cable length × cable output in W per ft

Where:

  • Pipe length is the length of pipe you want to trace. It has a unit selector, so you can enter metres.
  • The wrap multiplier is 1 for a straight run and 1.5 for a spiral wrap. The 1.5 is the calculator own assumption, and the real figure depends on how tightly you wind the cable.
  • Cable output is the rated watts per foot of the cable you plan to use, with a starting value of 5.

The wattage is a nominal figure. The output of a self-regulating cable changes with the temperature of the pipe, so read the datasheet of the cable you buy.

Worked examples

A straight run on a 100 ft pipe

Cable length = 100 × 1 = 100 ft. Running wattage = 100 × 5 = 500 W.

The same pipe with a spiral wrap

Cable length = 100 × 1.5 = 150 ft. Running wattage = 150 × 5 = 750 W.

A short run with a higher output

A pipe of 60 ft with a straight run and a cable of 8 W per foot needs 60 ft of cable and 60 × 8 = 480 W. With a spiral wrap it needs 90 ft and 90 × 8 = 720 W.

A long run

A pipe of 250 ft with a straight run at 5 W per foot needs 250 ft of cable and 1,250 W.

From watts to current

Current = watts ÷ volts. A load of 500 W on a 120 V supply draws 500 ÷ 120 = 4.2 A, and 750 W draws 6.25 A. The calculator does not ask for the voltage, so work this out yourself, and check the datasheet for the maximum circuit length and the breaker size for your cable.

Choosing the cable and checking the design

A heat trace design guide explains that the output you need depends on how much heat the pipe loses. The heat loss is Q = k × A × ΔT ÷ t, where k is the thermal conductivity of the insulation, A is the surface area, ΔT is the difference between the pipe temperature and the outside temperature, and t is the insulation thickness. The type and thickness of the insulation are therefore required inputs. The same guide says the choice of cable depends on the temperature you want to maintain, the lowest and highest outside temperatures, and the highest temperature the pipe will meet. It gives about 9 W per foot as a general figure, but says this varies with the system and the environment. The calculator has no heat-loss step, so choose the output from the manufacturer tables.

Allowances the calculator leaves out

The guide notes that valves, flanges, pumps and pipe supports act as heat sinks and need extra cable, as do splices, tees and power connections. Its baseline is 1 ft of cable for 1 ft of pipe, with the cable on the lower side of the pipe. The calculator does not add the extra footage, so add the allowance from the cable datasheet to the cable length. For example, if the datasheet asks for 2 ft per valve, which is only an illustration, four valves add 8 ft.

Electrical protection

The guide states that the National Electrical Code requires ground-fault equipment protection for heat trace circuits. Have the circuit checked by a qualified electrician, and follow the installation instructions for the cable.

Using the estimate

The result tells you roughly how much cable to buy and how much power it uses. Cable is sold in set lengths, so round up to the next available length. For a long or complex system, or one that carries a process fluid, use the manufacturer design software or an engineer, since a simple length and wattage estimate does not replace a full design.

For other heating jobs, see the radiant floor heating cost calculator, the radiant heat layout calculator and the pool heater sizing calculator.

Checking the design before you buy

Before you buy, check three things on the datasheet of the cable: the maximum length of one circuit at your voltage and breaker size, the extra cable needed for fittings, and the pipe materials and insulation the cable is rated for. If the total length is more than one circuit allows, split the run into two circuits. Keep the cable and the insulation dry, and follow the installation instructions.

Frequently asked questions

How much heat trace cable do I need?

A straight run needs about 1 ft of cable for every foot of pipe, and a spiral wrap uses 1.5 times as much in this calculator. Add extra cable for valves, flanges and connections, as the cable datasheet says.

How many watts will the cable use?

Multiply the cable length by the rated watts per foot. A cable of 100 ft at 5 W per foot gives 500 W. The real output of a self-regulating cable changes with the pipe temperature.

What watts per foot should I choose?

It depends on the heat the pipe loses, which depends on the insulation, the pipe size and the temperature difference. A heat trace guide gives about 9 W per foot as a general figure but says it varies, so use the manufacturer tables.

Does the calculator include valves and fittings?

No. Valves, flanges, pumps and supports need extra cable, so add the allowance from the cable datasheet to the result.

Mark Danny

Mark Danny

Mark Danny builds and maintains the free calculators and guides on Area of Irregular Shapes Calculator. Every calculator page explains its formula and shows a worked example, so you can check the working yourself. Spotted a mistake or have a suggestion? Email gulsher.hingoro101@gmail.com.

Articles: 559