Metal Roof Cost Calculator: Panels, Labor & Tear-Off

A metal roof is priced by the square foot of roof surface, not by the footprint of the house. Enter the roof footprint, the pitch, and your panel, labour and tear-off prices, and this calculator returns the roof surface area and an estimated total.

Roofing Calculators

Metal Roof Cost Calculator

Installed cost of a standing-seam or corrugated metal roof, from footprint, pitch and panel/labour pricing.

4:12 ≈ 1.054, 6:12 ≈ 1.118, 8:12 ≈ 1.202, 12:12 ≈ 1.414
Example price — replace with your local quote.
Example price — replace with your local quote.
Roof area = footprint area × pitch multiplier (accounts for slope). A 4:12 pitch ≈ 1.054×, 6:12 ≈ 1.118×, 8:12 ≈ 1.202×, 12:12 ≈ 1.414×.

Starting values: the calculator opens with a 40 ft by 30 ft footprint, a pitch multiplier of 1.118 (a 6:12 roof), a panel price of 8 and installation labour of 4 per square foot, and no tear-off. Those prices are example figures, not quotes, so replace them with prices from your own contractor or supplier. With them the roof surface is 1,341.6 sq ft and the estimate is about $16,099.

How the estimate is built

Metal panels cover the sloped surface of the roof, which is larger than the floor area underneath it. The calculator first converts the footprint to roof surface, then multiplies by the combined price per square foot:

Roof area = Length × Width × Pitch multiplier

Total = Roof area × (Panel price + Labour price + Tear-off price)

Where:

  • Length and Width = the roof footprint seen from above
  • Pitch multiplier = the factor that accounts for the slope
  • Panel price = the metal panel cost per square foot of roof
  • Labour price = the installation cost per square foot of roof
  • Tear-off price = the cost to remove the old roof per square foot, or 0 if none

The pitch multiplier

Pitch is written as rise over a 12-inch run. The multiplier comes from the Pythagorean relationship: Multiplier = √(1 + (rise ÷ 12)²). That gives about 1.054 for 4:12, 1.118 for 6:12, 1.202 for 8:12 and 1.414 for 12:12. For 6:12, √(1 + 0.25) = √1.25 = 1.118. Measure the footprint over the eaves, since the roof surface continues past the walls to the edge of the overhang.

Worked examples

Example 1: the default roof

Roof area = 40 × 30 × 1.118 = 1,341.6 sq ft, which is about 13.4 roofing squares (one square is 100 sq ft). Price per square foot = 8 + 4 + 0 = 12. Total = 1,341.6 × 12 = $16,099.

Example 2: a shallower roof with tear-off

A 40 ft by 30 ft footprint at 4:12 (multiplier 1.054) has a roof area of 1,200 × 1.054 = 1,264.8 sq ft. Take a panel price of 6, labour of 4 and tear-off of 1.5, so the combined price is 11.5 per sq ft. Total = 1,264.8 × 11.5 = $14,545. These prices are only an illustration.

Example 3: a steeper, larger roof

A 50 ft by 30 ft footprint at 8:12 (multiplier 1.202) has a roof area of 1,500 × 1.202 = 1,803 sq ft. At the default 12 per sq ft, the total is 1,803 × 12 = $21,636. Steeper pitch raises the surface area and, in practice, labour as well, which the calculator cannot see.

Example 4: adding a waste allowance

The calculator does not add waste. Contractors commonly order extra material, and about 10% is often cited for waste on a metal roof. On Example 1, panels for 1,341.6 sq ft at 8 cost $10,732.80. Ordering 10% more means 1,475.76 sq ft, or $11,806.08, which is $1,073.28 more. Your contractor’s quote will say how much waste it assumes.

What drives the price of a metal roof

  • Metal type. Material is the largest cost driver. Copper is the most expensive option, while zinc, steel and tin are generally lower in cost.
  • Panel profile. Corrugated panels are typically the most affordable. Standing seam panels, with concealed fasteners, cost more. Metal shingles are often cheaper than standing seam.
  • Labour. It is a large share of the bill. One roofing guide puts labour at about 60% of total replacement cost. With the example prices here labour is a third, so check the split in your own quote.
  • Pitch and complexity. Roofs steeper than 6:12 are harder and more dangerous to work on. Skylights, chimneys and other features add flashing cost.
  • Finish. Paint systems such as PVDF and SMP differ in fade, corrosion, scratch and crack resistance.
  • Trim, flashing and underlayment. Trim cost depends on the metal type, and an existing underlayment may not suit a metal roof.

Using a contractor quote

Contractors often quote per roofing square, which is 100 sq ft. To compare, convert the calculator’s per-square-foot price: 12 per sq ft is 12 × 100 = 1,200 per square. Divide a quote per square by 100 to enter it as a per-square-foot price.

What the calculator does not do

  • It treats the roof as one rectangle at one pitch. For a roof with several sections or slopes, run each section separately and add the totals.
  • It does not add waste, trim, flashing, underlayment, skylight work, permits or disposal, so add those if your quote lists them.
  • It does not quote local prices. The panel, labour and tear-off prices are yours to enter.

To compare materials, see the roof replacement cost calculator and the asphalt shingle roof cost calculator, and for the exterior walls the siding cost calculator.

Frequently asked questions

How do I calculate the cost of a metal roof?

Multiply the footprint length and width by the pitch multiplier to get roof area, then multiply by the combined price per square foot of panels, labour and any tear-off. The default 40 ft by 30 ft roof at 6:12 is 1,341.6 sq ft.

What pitch multiplier should I use?

Use the factor for your roof slope: about 1.054 for 4:12, 1.118 for 6:12, 1.202 for 8:12 and 1.414 for 12:12. It equals the square root of 1 plus (rise divided by 12) squared.

Does the calculator include waste and trim?

No. It prices roof area only. Roofers commonly order extra material, with about 10% often cited for waste, and trim, flashing and underlayment are separate costs.

How do I compare my quote, which is per square?

A roofing square is 100 square feet. Divide a per-square price by 100 to get the per-square-foot figure the calculator uses.

Mark Danny

Mark Danny

Mark Danny builds and maintains the free calculators and guides on Area of Irregular Shapes Calculator. Every calculator page explains its formula and shows a worked example, so you can check the working yourself. Spotted a mistake or have a suggestion? Email gulsher.hingoro101@gmail.com.

Articles: 559