Thermal Expansion Calculator: Linear Length Change

This thermal expansion calculator finds how much a material changes in length when its temperature changes. Enter the original length, the temperature change and the coefficient of linear expansion, and it returns the change in length in feet and in inches.

Rates Calculators

Thermal Expansion Calculator

Linear thermal expansion (change in length) for any material, from its original length, temperature change, and coefficient of linear thermal expansion.

°F
×10⁻⁶ /°F
Commonly cited approximate values (×10⁻⁶ per °F): aluminum ≈ 13.1, steel ≈ 6.5, copper ≈ 9.5, PVC ≈ 30 — enter the value for your specific material/alloy.

Starting values: the calculator opens with a length of 10 ft, a temperature change of 50°F and a coefficient of 13.1 × 10−6 per °F, the figure for aluminium. The change in length is 0.00655 ft, which is 0.0786 inches.

The formula

ΔL = L0 × α × ΔT

Where:

  • ΔL = the change in length
  • L0 = the original length
  • α = the coefficient of linear thermal expansion, per degree
  • ΔT = the temperature change, final minus initial

An engineering reference explains that the change in length is proportional to both the original length and the temperature change. Double the length or double the temperature swing and you double the expansion. The result is positive for heating. If the temperature falls, enter a negative change, and the result is a contraction.

Coefficients: values and units

The calculator takes the coefficient in units of × 10−6 per °F and its hint lists approximate values: aluminium about 13.1, steel about 6.5, copper about 9.5 and PVC about 30. Treat these as starting points. Real values vary with the exact alloy or compound and with temperature.

The engineering reference lists coefficients in × 10−6 per °C instead. Its figures include carbon steel at 10.8 to 12.5, aluminium at 23, copper at 16 to 16.7 and PVC at 54 to 110. It says the values are mostly at 25°C and that the ranges come from variations in materials and sources. To convert a coefficient from per °C to per °F, multiply by 5 ÷ 9 (about 0.556). Steel at 10.8 to 12.5 becomes roughly 6.0 to 6.9 per °F, which agrees with the tool’s 6.5. Aluminium at 23 becomes about 12.8 per °F, close to the 13.1 hint. PVC at 54 to 110 becomes about 30 to 61 per °F, so the hint of 30 is at the lower end of that range. For plastics, check the value for your product.

A shortcut for metric users

The coefficient and the temperature change are multiplied together, and converting one by 5 ÷ 9 while converting the other by 9 ÷ 5 cancels out. So you can enter a temperature change in °C along with a coefficient in × 10−6 per °C and get the same answer. Just keep the pair consistent. The labels in the calculator say °F, but the arithmetic does not care, as long as both values use the same scale. The length can be entered in other units, and the result is given in feet and inches.

Worked examples

Example 1: the default

10 ft × 13.1 × 10−6 × 50 = 0.00655 ft. Times 12 gives 0.0786 in. A 10 ft aluminium run grows by about 0.08 inches over a 50°F rise.

Example 2: steel

The same length and temperature change with a coefficient of 6.5: 10 × 6.5 × 10−6 × 50 = 0.00325 ft, or 0.039 in. Steel expands about half as much as aluminium.

Example 3: PVC pipe

With a coefficient of 30: 10 × 30 × 10−6 × 50 = 0.015 ft, or 0.18 in. Plastic pipe moves several times more than metal for the same length, which is why long plastic runs need expansion allowance.

Example 4: a long aluminium run on a hot day

A 20 ft aluminium run sees a 70°F swing between a cold morning and a hot afternoon. ΔL = 20 × 13.1 × 10−6 × 70 = 0.01834 ft, or 0.220 in.

Example 5: contraction

A 10 ft copper bar (coefficient 9.5) cools by 40°F. Enter −40. ΔL = 10 × 9.5 × 10−6 × (−40) = −0.0038 ft, or about 0.046 in shorter.

Where expansion matters

  • Pipework and railings, which need expansion joints or loops.
  • Bridges, decking and roofing, which use gaps and sliding supports.
  • Cladding and fascia boards, where a fixed fastening can buckle the material.
  • Fits between parts of different materials, where uneven expansion can loosen or jam them.

Limits of the linear formula

The formula treats the coefficient as constant over the temperature range, which is a good approximation for modest changes. For large ranges the coefficient shifts, and for area or volume expansion you need a different relationship. The tool gives length change only, and it is the free change. It does not include the force created when the material is restrained.

Working out gaps for a real installation

The change in length is the free movement of the material. To use it in a design, decide the largest temperature swing the part will see in service, enter that as the temperature change, and compare the result with the gap, slot or loop you have allowed. Add a margin, because the real swing may be larger than the air temperature suggests: parts in direct sun can run hotter than the air around them.

Comparing materials side by side

For a 10 ft length and a 50°F rise, the movement is 0.039 in for steel, 0.057 in for copper (coefficient 9.5), 0.079 in for aluminium and 0.18 in for PVC using the calculator’s hint values. Ranking them: PVC moves more than four times as much as steel, and aluminium about twice as much. If two different materials are joined and heated together, the difference between their movements is what stresses the joint.

Scaling the answer

Because the relationship is proportional, you can scale a result without recalculating. If 10 ft of aluminium moves 0.0786 in for a 50°F rise, then 30 ft moves three times as much, 0.236 in, and a 100°F rise doubles that again. This is a handy check on your own answers.

Frequently asked questions

What is the thermal expansion formula?

The change in length equals the original length times the coefficient of linear expansion times the temperature change.

What coefficient should I use?

Use the value for your specific material. The calculator’s hint lists approximate values per degree Fahrenheit for aluminium, steel, copper and PVC. Plastics vary widely, so check the product data.

Can I use Celsius?

Yes, if you enter both the temperature change and the coefficient in Celsius terms. The two must use the same scale. Multiplying them gives the same answer either way.

How do I calculate contraction?

Enter a negative temperature change for cooling. The result is negative, meaning the material gets shorter.

Mark Danny

Mark Danny

Mark Danny builds and maintains the free calculators and guides on Area of Irregular Shapes Calculator. Every calculator page explains its formula and shows a worked example, so you can check the working yourself. Spotted a mistake or have a suggestion? Email gulsher.hingoro101@gmail.com.

Articles: 579