This air changes per hour calculator tells you how many times the air in a room is replaced in an hour. Enter the airflow in CFM and the room volume, and it returns the ACH figure.
Air Changes Per Hour Calculator
Air changes per hour (ACH) for a room, from the ventilation airflow rate and room volume.
Starting values: the calculator opens with an airflow of 200 CFM and a room volume of 2,000 cubic feet. The result is 6.00 air changes per hour.
The formula
ACH = (CFM × 60) ÷ Room Volume (ft³)
Where:
- CFM = airflow in cubic feet per minute
- 60 = minutes in an hour, converting the flow to cubic feet per hour
- Room Volume = length × width × height of the room, in cubic feet
The volume input accepts other units and is converted to cubic feet before the calculation. To go the other way, rearrange it: CFM = ACH × Volume ÷ 60. An engineering reference states the same relationship as flow equals the air change rate times the room volume.
Worked examples
Example 1: the default
200 × 60 = 12,000 cubic feet per hour. Divided by 2,000 cubic feet, that is 6.00 ACH. The air in the room is replaced six times each hour, or once every 10 minutes on average.
Example 2: a small bedroom
A room is 12 ft by 15 ft with an 8 ft ceiling, so its volume is 12 × 15 × 8 = 1,440 cubic feet. A fan moves 120 CFM. ACH = 120 × 60 ÷ 1,440 = 5.00.
Example 3: sizing the fan for a target rate
An office is 2,400 cubic feet and you want 4 ACH. CFM = 4 × 2,400 ÷ 60 = 160 CFM. For 3 ACH you would need 120 CFM.
Example 4: a metric room
A room of 56.6 cubic metres is about 2,000 cubic feet, the same as the default. At 200 CFM the result is again 6.00 ACH. One CFM is about 1.699 cubic metres per hour, so you can convert flow from cubic metres per hour by dividing by 1.699.
Typical rates: a reference, not a rule
An engineering reference lists commonly used air change rates per hour for different spaces. These are guide figures for ventilation design, not per-person calculations, and local codes and standards take precedence.
- Residences: 1 to 2
- Offices: 3 to 4
- Retail shops: 6 to 10
- Hospital rooms: 4 to 6
- Restaurants: 8 to 12
- Kitchens: 15 to 60
- Swimming pools: 20 to 30
The ranges are wide because the right rate depends on the use of the space, heat and moisture loads, and any contaminants. Use the table to get a feel for the scale, then follow the standard or code that applies to your building.
What ACH does and does not tell you
- ACH is an average. It assumes the supply air mixes well, but poor circulation can leave some corners with stale air even at a high ACH.
- A rate of 6 ACH does not mean all the old air is gone in 10 minutes. Mixing means some air is replaced several times while some stays.
- Total airflow depends on duct losses and filter condition, so measured CFM at the outlet is better than the fan’s nameplate figure.
Measuring the inputs
For airflow, use a measured value where you can, such as a balancing report or an anemometer reading, or the manufacturer’s rating at your operating point. For volume, multiply the room’s length, width and height. For an irregular space, split it into rectangles and add the volumes. If you are sizing cooling as well as ventilation, the room BTU calculator covers the heat load, which is a separate question from the air change rate.
Worked scenario: checking a ventilation fan against a target
A workshop measures 30 ft long, 20 ft wide and 10 ft high, so its volume is 6,000 cubic feet. An exhaust fan is rated at 500 CFM. ACH = 500 × 60 ÷ 6,000 = 5.00. If you wanted 8 ACH for the same space, you would need 8 × 6,000 ÷ 60 = 800 CFM, so the single fan falls short by 300 CFM. You could add a second fan of at least that capacity, though the measured airflow at the installed position is what counts.
Time for one air change
Divide 60 by the ACH to get the average minutes per air change. At 6 ACH it is 10 minutes. At 12 ACH it is 5 minutes. The figure is a convenient way to describe a rate, but it is an average and does not mean that a room is fully flushed in that time.
Why volume matters as much as airflow
The same fan gives very different results in rooms of different size. The 200 CFM of the default gives 6 ACH in a 2,000 cubic foot room but only 3 ACH in a 4,000 cubic foot room. When a room has a high ceiling, include the full height in the volume. A common mistake is to measure floor area and forget the third dimension, which makes the room look smaller than it is and the ACH look larger.
Frequently asked questions
How do I calculate air changes per hour?
Multiply the airflow in CFM by 60 and divide by the room volume in cubic feet. A 2,000 cubic foot room with 200 CFM of airflow has 6 air changes per hour.
How many CFM do I need for a given ACH?
Multiply the target ACH by the room volume and divide by 60. For 4 ACH in a 2,400 cubic foot room, you need 160 CFM.
What is a good ACH for a room?
It depends on the use of the space. Reference tables list about 1 to 2 for homes and 3 to 4 for offices, with much higher figures for kitchens and pools. Local codes set the actual requirements.
Does a higher ACH always mean cleaner air?
Not always. ACH is an average, and air may not mix evenly. Where the air enters and leaves also matters, as does what the air is filtered or exhausted of.
