Parts Per Hour Calculator: Manufacturing Throughput

This parts per hour calculator estimates how many good parts a machine or line turns out in an hour. Enter the cycle time, the number of parts made per cycle, the share of time the machine is running and the first-pass yield, and it returns good parts per hour.

Rates Calculators

Parts Per Hour Calculator

Manufacturing throughput in parts per hour, from cycle time and (optionally) downtime/scrap losses.

sec
%
%

Starting values: the calculator opens with a 12-second cycle, 1 part per cycle, 90 percent availability and 98 percent first-pass yield. The result is 264.6 good parts per hour.

The formula

Good Parts per Hour = (3,600 ÷ Cycle Time) × Cavities × Availability × Yield

Where:

  • 3,600 = the number of seconds in an hour
  • Cycle Time = seconds per cycle, so 3,600 ÷ Cycle Time is the number of cycles in an hour at full speed
  • Cavities = parts produced in each cycle, such as the cavities in a mould or the parts on a fixture
  • Availability = the share of the hour the machine is actually producing, as a percentage
  • Yield = the share of parts that pass first time, as a percentage

The first piece, (3,600 ÷ Cycle Time) × Cavities, is the theoretical rate: what the machine would make if it ran without a stop and every part was good. Availability and yield then reduce that to what you can actually ship.

How this relates to OEE

Overall equipment effectiveness, or OEE, is a standard way to describe manufacturing performance. It is the product of three factors: Availability × Performance × Quality. Availability is run time divided by planned production time. Performance compares the ideal cycle time with the actual one. Quality is good parts divided by total parts.

This calculator uses two of the three. The availability and first-pass yield inputs correspond to availability and quality. There is no separate performance input, so enter the cycle time your machine actually achieves on average, including any slow running. If you enter the ideal or nameplate cycle time instead, the result will be higher than what you will really get.

Worked examples

Example 1: the default

  1. Cycles per hour at full speed = 3,600 ÷ 12 = 300.
  2. Parts per hour at full speed = 300 × 1 = 300.
  3. Apply availability: 300 × 0.90 = 270.
  4. Apply yield: 270 × 0.98 = 264.6 good parts per hour.

Over an 8-hour shift that comes to 264.6 × 8 = 2,116.8 good parts, if the 90 percent availability holds across the whole shift.

Example 2: a multi-cavity tool

A moulding machine has a 30-second cycle and a 4-cavity tool. Availability is 85 percent and yield is 95 percent.

  1. Cycles per hour = 3,600 ÷ 30 = 120.
  2. Parts per hour at full speed = 120 × 4 = 480.
  3. 480 × 0.85 = 408, and 408 × 0.95 = 387.6 good parts per hour.

Example 3: theoretical output only

A press runs a 45-second cycle and makes 2 parts per cycle. With availability and yield both set to 100 percent, the result is (3,600 ÷ 45) × 2 = 160 parts per hour. This is the ceiling for that machine. Any real figure will be lower.

Example 4: the OEE figures from a published case

The OEE reference site works through a 480-minute shift with a 60-minute break and 47 minutes of downtime. The ideal cycle time is 1 second, the machine produced 19,271 parts and 423 were rejects.

  • Planned time = 480 − 60 = 420 minutes. Run time = 420 − 47 = 373 minutes. Availability = 373 ÷ 420 = 88.81 percent.
  • Performance = (1 second × 19,271) ÷ (373 × 60 seconds) = 86.11 percent.
  • Quality = (19,271 − 423) ÷ 19,271 = 97.80 percent.
  • OEE = 88.81 × 86.11 × 97.80 percent = 74.79 percent.

For this calculator, you could enter an availability of 88.81, a yield of 97.80 and the average actual cycle time, which is 22,380 seconds of run time divided by 19,271 parts, about 1.161 seconds. The hourly result will then reflect all three factors, since the slower actual cycle already carries the performance loss.

Getting realistic inputs

  • Cycle time: time several consecutive cycles and use the average, not the best one.
  • Cavities: count only the parts that become saleable. A shot with a runner or a scrap piece does not count as extra parts.
  • Availability: remove planned stops such as breaks from the base time, then record the unplanned downtime from tool changes, jams and waiting.
  • Yield: use first-pass yield, the share that passes without rework. Reworked parts are not first-pass good.

What the calculator does not do

It does not model start-up losses, changeovers within the hour, shift patterns or a bottleneck elsewhere on the line. A machine can only produce as fast as the slowest step feeding or following it, so check the rate of the constraint, not just this machine. If you are estimating cost per part, combine the result with your hourly machine rate by hand.

Using the result to compare machines or plan a shift

Parts per hour becomes more useful when you set two scenarios side by side. Keep the same cycle time and change only availability: at 90 percent the default machine gives 264.6 good parts per hour, while at 80 percent it gives 300 × 0.80 × 0.98 = 235.2. A ten-point change in availability moves output by 29.4 parts every hour, which is 235 parts across an 8-hour shift. Small losses add up quickly.

Working back to the time needed

To find how long a batch will take, divide the order quantity by the good parts per hour. An order of 5,000 good parts at 264.6 per hour needs 5,000 ÷ 264.6 = 18.9 hours of production time. If the order must be shipped sooner, the three levers are a shorter cycle, more parts per cycle, or better availability and yield. Raising the cavities from 1 to 2 doubles the theoretical rate, but only if the machine can fill and eject both parts within the same cycle time.

Frequently asked questions

What is the formula for parts per hour?

Good parts per hour = (3,600 divided by cycle time in seconds) times parts per cycle times availability times first-pass yield, with availability and yield as decimals.

Should I use ideal or actual cycle time?

Use the average actual cycle time. The calculator has no separate performance factor, so slow running is only captured if the cycle time you enter reflects it.

What is the difference between availability and yield?

Availability is the share of the time the machine is producing. Yield is the share of the parts made that are good the first time. Both reduce the theoretical output.

Is this the same as OEE?

Not exactly. OEE multiplies availability, performance and quality. This tool covers availability and quality, and performance enters through the cycle time you use.

Mark Danny

Mark Danny

Mark Danny builds and maintains the free calculators and guides on Area of Irregular Shapes Calculator. Every calculator page explains its formula and shows a worked example, so you can check the working yourself. Spotted a mistake or have a suggestion? Email gulsher.hingoro101@gmail.com.

Articles: 579